Hot Spring Portable Spa How To Turn On

If you lead a busy life or don't consider yourself mechanically inclined, you may be concerned that hot tub maintenance will be difficult or counterbalance the stress relief a hot tub provides. Fortunately, regular HotSpring spa maintenance is quick and easy. In this blog we put together a guide for HotSpring Spas locks and troubleshooting, to make it even easier for you lot!

AUXILIARY Control PANEL

The auxiliary control panel, conveniently located in the spa seating area (Vista®, Grandee®, Envoy®, Vanguard®, Sovereign®, Aria™, and Prodigy® models) allows the user to activate the jets, light, and Spaudio® functions from inside the spa. If there is a trouble with the AUXILIARY CONTROL Console it volition be unresponsive, delight then BOOK A SERVICE Telephone call with us.

INDICATOR LIGHTS

At a glance, the indicator lights are readily visible on the main control console.

The iii indicator lights: POWER, READY and CLEAN, piece of work independently from the rest of the command panel display. That way, even if the control console is off, you lot can simply glance at the "READY" indicator light to determine whether or non your spa is within the range of your set temperature.

• Power Indicator: The POWER indicator is 'on' when the spa is properly supplied with power. Information technology as well provides a diagnostic function–a blinking ability indicator indicates that the heater high limit has tripped, meaning that either the spa water is above its adequate temperature range, or a malfunction has occurred within the spa (such as low circulation due to clogged filters). An 'off' power indicator ways that there is a problem with the spa command box or the ability supplied to the spa.
• Ready Indicator: The READY indicator volition calorie-free when the spa water temperature is inside 2-1/2°F (i.4°C) of the set up temperature, and will turn off when the temperature is outside of that range. If you increase or decrease the temperature setting of the spa, the ready indicator will turn off until the spa temperature reaches the acceptable range for the new ready temperature. Additionally, a blinking READY indicator indicates that a trouble exists with the temperature sensor.
• Make clean Indicator: The Make clean indicator lights up when the Make clean button is pressed. It remains on during the ten-infinitesimal clean cycle (used for h2o maintenance), then automatically shuts off at the end of the bike. The JET symbol will also illuminate on the brandish to indicate that the jet pump is on.

LOCKING FEATURES

The 2 locking features, TEMPERATURE LOCK and SPA LOCK, are enabled from the main command console by pressing a specific combination of buttons. In one case enabled, a lock will remain active until the specific button combination is applied to disable the lock. Even if ability is disconnected from the spa and presently thereafter reapplied (such every bit in a power outage) the lock volition remain in place.

SPA LOCK

The SPA LOCK feature deactivates all of the functions of the main and auxiliary command panels. It is mostly used to forbid unwanted use of the spa. To activate the SPA LOCK, press the LIGHT minus (-) and TEMP minus (-) buttons at the same time and concur them downwardly until the give-and-take SPA and the lock symbol are illuminated on the display (approximately ii seconds). When the SPA LOCK is activated, if a push button is pressed, the control panel will display the lock symbol and the discussion SPA for 30 seconds, and so plough off. To deactivate the SPA LOCK, printing the LIGHT minus (-) and TEMP minus (-) buttons at the same time and hold them down until the discussion SPA and the lock symbol are no longer illuminated on the display (approximately ii seconds).

TEMPERATURE LOCK

The TEMPERATURE LOCK feature deactivates the temperature command function of the chief control panel. All other functions on the main and auxiliary command panels volition operate normally. TEMPERATURE LOCK is most often used past people who practice not desire others to tamper with or modify the set temperature of the spa water. To activate the TEMPERATURE LOCK, printing the LIGHT plus (+) and TEMP plus (+) buttons at the same time and agree them downward until the words Fix TEMP, the numerical set temperature value and the lock symbol are illuminated on the display (approximately two seconds).

When the TEMPERATURE LOCK is activated, the JETS, LIGHT, and Make clean buttons volition operate normally, and the temperature setting tin can exist viewed simply can Non exist inverse. If a temperature button is pressed, the command panel will brandish the lock symbol and the set temperature for 30 seconds, so turn off. To conciliate the TEMPERATURE LOCK, press the LIGHT plus (+) and TEMP plus (+) buttons at the same time and hold them down until the lock symbol is no longer illuminated on the display (approximately two seconds).

Master Control Console BUTTONS & DISPLAY

The master command panel has buttons which the spa user presses to set up the temperature, initiate the clean cycle, vary the intensity of the low-cal, and activate or deactivate the jet pump. With the exception of the CLEAN button, the command console display responds to let you know you've pressed a button, and that the selected function has been performed. After a catamenia of non-utilize, pressing any push button will wake up a sleeping display, likewise as performing its role.

TEMPERATURE CONTROL

The fix temperature range is from eighty°F to 104°F (27°C to twoscore°C). (The temperature of any setting may ascent slightly depending on the current utilize and condition of your spa, and on outside temperatures.) The set up temperature of the spa water will automatically be 102°F (39°C) the first fourth dimension that ability is applied. This is the setting programmed at the manufactory. After the spa has been set up and used, the last temperature value set by the user will be stored in memory. If power is disconnected from the spa, it will automatically revert to the last set temperature when power is reapplied. To display the ready temperature of the spa, press the TEMP plus (+) push button. The set up temperature will exist displayed, unless the spa is locked (in which case the word SPA is displayed with the lock symbol). The set temperature brandish will automatically shut off after 30 seconds.

To increase the fix temperature of the spa water, press the TEMP plus (+) button. Each time the push button is pressed, the set temperature display will increment by one degree. If the push is held downward, the set temperature display will increase by 1 degree every half-second. To subtract the set up temperature of the spa h2o, press the TEMP minus (-) push. Each fourth dimension the push is pressed, the prepare temperature display will decrement past one degree. If the button is held down, the set temperature display volition decrease by ane degree every half-2nd. If the set up temperature value will not change, check the TEMP LOCK and SPA LOCK features. When either of these features is applied, the temperature control is disabled.

JETS Control

At that place are two buttons (three buttons on Vista® ,Grandee®, Envoy®, Aria™ and Vanguard® models) which touch on the jet pump(s):The JETS button (all models) / JETS 1 (Vista, Grandee, Envoy, Aria and Vanguard models only) activates the jet pump.

• When the JETS or JETS 1 button is pressed, the jets symbol volition illuminate on the control panel display. The symbol will remain lit until the push button is pressed to plow off the jet pump, or subsequently ii hours of continuous functioning when the pump is automatically shut off by the control system.
• The JETS 2 button (Vista, Grandee, Envoy, Aria and Vanguard only) activates the second jet pump. When the JETS 2 push button is pressed, the jets symbol volition illuminate on the control panel brandish. (Vista, Envoy & Aria will run in low speed with first press and loftier speed with second press). The symbol will remain lit until the button is pressed to turn off the jet pump, or after two hours of continuous performance when the pump is automatically close off by the control system.
• The Make clean button, provided as a convenient timer for h2o maintenance, activates the jet pump for a ten minute catamenia. The Make clean indicator volition turn on and the JET symbol on the display volition illuminate to indicate the jet pump is engaged.

Next, y'all may add together properly measured spa h2o chemicals into the filter compartment. The jet pump and clean indicator will automatically shut off afterwards ten minutes. If the jet pump will not engage, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control panels.

Lite CONTROL- STANDARD

The intensity of the spa'due south low-cal is controlled using the LIGHT plus (+) or LIGHT minus (-) buttons. To turn on the spa light, press the Light plus (+) button. The light will plow on at maximum intensity and the light symbol will illuminate on the control panel display. To reduce the intensity of the light, printing the Calorie-free minus (-) push button. The intensity of the light volition decrease each time the button is pressed. Additionally, if either of the Low-cal buttons (+ or -) on the Chief Control panel only, are held down, the calorie-free intensity will increase or decrease at the charge per unit of one intensity level every half-second.

To plow off the light, concur the Low-cal minus (-) push button. The low-cal volition dim and turn off. When the light turns off, the low-cal symbol on the display will too turn off. If the lite is left on, it will automatically be turned off by the control system after six hours of continuous operation. The light symbol on the console volition also turn off when the low-cal is deactivated. If the light will not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control panels.

Calorie-free Command- Brilliance

All Hot Spring spas are equipped with the Brilliance (Multi-Color) light. The intensity of the spa'south light is controlled using the Low-cal Plus (+) or LIGHT Minus (-) buttons. At that place are 5 (five) brightness levels plus off. To turn on the spa calorie-free, printing the Calorie-free Plus (+) button. The low-cal will turn on at maximum intensity and the calorie-free symbol volition illuminate on the control panel display. When the light is set to its maximum brightness setting, press the Lite Plus (+) button to modify the colour. The color loop sequence is fix as follows: Blue, Aqua, Greenish, White, Bister, Red, Loop ON, Loop OFF. To activate the color loop, press (+) after the color ruby-red. The colors will automatically run through the sequence in the order listed to a higher place. To stop the loop press the LIGHT Plus (+) push button while the loop is on and the brightness setting is in the maximum position. To reduce the intensity of the light, press the Lite Minus (-) push.

 The intensity of the calorie-free will decrease each time the button is pressed. Additionally, if the Lite Minus (-) button on the Principal Control panel just, is held downwards, the light intensity will decrease at the rate of one intensity level every half-second until it shuts off. If the intensity of light is below the maximum effulgence and the LIGHT Plus (+) button is pressed and held down, the calorie-free will increase intensity until it reaches maximum brightness, it will so proceed through the color sequence every half-second until the button is released. To plow off the light, hold the Lite Minus (-) button. The light will dim and turn off. When the lite turns off, the light symbol on the brandish volition also turn off. If the light is left on, it will automatically be turned off by the control system afterward 6 hours of continuous performance. The light symbol on the console will also plough off when the light is deactivated. If the light will not turn on, brand certain SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary command panels.

Summertime Style DISPLAY

The Summertime Mode symbol is on when the Summertime Mode timer is on. When activated, the symbol will be visible fifty-fifty in bright light when the primary display backlight is off. In depression light conditions, the Summertime Style symbol will only be visible when the brandish is activated past pressing a control panel button.

Your Hot Spring spa is equipped with a Summertime Way timer. The Summer Mode timer can be activated during extremely hot summer months if it becomes difficult to maintain h2o temperatures low enough for comfort. Upon switching to the ON fashion, the heater volition immediately shut downwardly while the circulation pump (which can add heat to the water through normal performance) will remain on for approximately 5 minutes for heater cool downwardly. Both heater and apportionment pump will remain off for the next 8 hours.

Additionally, the summer mode display on the main command console will actuate and remain active for every bit long every bit the summer fashion is on. Following this eight-hour period, the apportionment pump and heater will automatically restart and volition operate normally for the next sixteen hours. The circulation pump and heater will keep to turn off for an viii-hour period every day that the switch remains in the ON position. In this manner, the amount of heat transferred to the spa h2o will be minimized. When the outside temperatures begin to cool, the Summertime Style timer should be turned to the OFF position (the summer mode display on the main command panel will get out). This is the efficient 24 hour circulation mode that keeps the heater functioning and operating costs to a minimum during colder/heavier usage months.

Delight annotation that whenever power is disconnected and then reconnected to the spa, the Summertime Mode timer will reset starting with the eight-hour shutdown mode. If a different 8-hour shut down time is desired, conciliate the Summer Mode, and so reactivate at the first of the desired eight-60 minutes shut down time. The Summer Mode will not lower the spa's water temperature below the ambient air temperature.

To activate the Summertime Style, only follow these steps:

• Ready the temperature command to 80°F (26°C).
• On the command console, simultaneously press and hold for three seconds Temp Plus and Temp Minus buttons to activate the Summer Timer. The Summer Way must exist deactivated when cooler temperatures return.
• To do this, simply repeat step two.
• Delight exist enlightened that failure to deactivate the Summer Mode when the temperature drops beneath 32°F (0°C) will issue in freezing of the spa. Harm resulting from this situation is non covered nether the terms of the warranty.

If yous have any further questions or crave further help, please book a Hot Tub Service with us.

BOOK A HOT TUB SERVICE

Source: https://www.pioneerfamilypools.ca/advice/hotspring-spas-locks-trouble-shooting/

Share this post